4-128-1
Firetron Cell for 48PT1 Infrared Scanner
P-Series
|
4-263-1
Firetron Cell for 48PT2 Infrared Scanner.
C-Series, D-Series and Flame-Monitor.
|
4-314-1
Ultraviolet Tube for use in 45UV5-1005,
-1009, 45UV2, 45UV3-1050, C-Series, D-Series
and Flame-Monitor controls.
|
6-220 ,
6-221
Run-Reset Switch for MB System (6-220)
Start Switch MB System (6-221)
|
8-449
Plug-in Relay for MB Systems 120VAC RL1,
RL2, RL3
|
8-679
Plug-In relay for FE-5 Smoke system control
27PH7
|
10-88
Set of 3 Orifice Plugs. Drilled 1/16", 1/8",
3/16", 1/2". Pipe Thread. Also available:
10-15, Blank orifice plug for drilling to
any size required. For use with UV1A Scanner
|
27-196 ,
27-197 ,
27-198
Indicating Light Assembly
27-196 AMBER,
27-197 RED
27-198 WHITE
For use with MB Series Panel
|
29-223
Smoke system bellows for use with 27RL1 FE-4
System.
|
35-69
Heat Insulator. Reduces conduction of heat
from sight pipe to scanner. Used with 48PT1,
48PT2, UV-1A. 1/2" pipe connection.
|
35-127-1 (NPT)
35-127-3
(BSP)
Heating insulating nipples (Epoxyglass) for
use with 45UV2, 45UV5. 1-inch pipe size,
male both ends. Used to reduce conduction of
heat from scanner mount to scanner.
|
38-30
Replacement Meter Ringelman Scale for
FE-3/27VH6 Smoke Density Control.
|
38-33
Flame Signal Meter for 26RJ8, 26SJ5, 29RF5.
Indicates LOW and NORMAL flame signal
strength. |
|
38-42
Versatile Triplet multimeter for checking
flame signal continuity, line voltage and
other control circuit functions.
|
38-53
Flame Signal Meter. 0-25 Input.
|
38-58
Flame Signal Meter for 25RU8-4580 and
25SU5-4018. Scale 0-15 volts D.C. 20,000
ohms per volt.
|
38-59
Panel voltmeter 0-14VAC, 2 1/2 inches, for
30CK6. The meter is shown here inside the
55AF2 strip chart recorder.
|
38-71
30% Meter for 27RL1
|
38-74
Replacement Meter for FE-5 27PH7-1000 Smoke
System control.
|
38-96
Flame Meter, 2 1/4" square, 4-20ma
|
38-97
Flame Meter, horizontal, 4-20ma
|
46-38
Quartz Lens for use in 45UV5-1000, -1005,
-1006, -1007, -1008, and -1009 Scanners.
|
46-56
Quartz Lens. Used with 45UV3 to increase
scanner sensitivity. Replaces quartz window
in scanner.
|
48-87
Focal length 1 1/8 inch. Lens for 45RM1/RM2
scanners.
|
48-1805
Flame-Monitor E100 Mounting Screw
48-1836
Flame-Monitor E110 Mounting Screw
|
60-280
Pressure-tight mounting adapter. Used to
prevent positive pressure in breeching from
reaching light source (44DU2) and scanner
(47EM4) in FE-5 smoke density systems.
|
60-302
Swivel Mounting Adapter. Simplifies scanner
sighting. Used with 48PT1, 48PT2 and UV1A.
1/2" pipe connection.
|
60-460
Flame Signal attenuator permits reducing
flame signal amplified sensitivity 40% for
test purposes. Used in testing 6000 series
FP and FJ controls.
|
60-801
Sealing union with pyrex window. Seals
scanner signt pipe against excessive firebox
pressure. 100 p.s.i.g. rating. Used with
48PT1, 48PT2, 1/2" pipe connection.
|
60-1199
Sealing union with quartz window. Seals
scanner sight pipe against excessive firebox
pressure. 1" pipe thread. Used with 45UV1,
45UV2, 45UV3, 45UV5.
|
60-1257 ,
60-1290
Sealing union with quartz window (60-1257).
60-1290 has quartz lens to increase scanner
sensitivity. For use with UV1A/UV1B
scanners.
|
60-1664-3 (NPT)
60-1664-4
(BSP)
Scanner swivel mount for use with 45UV2,
45UV3, 45UV5. Simplifies scanner sighting.
|
60-2333
Line Filter for FLAME-MONITOR
|
61-2914-1
Shutter and Bracket Assembly for 45UV5-1005
thru -1009.
|
61-3263
Shutter, Bracket, and Lens Assembly for
45UV5-1005 thru -1009.
|
61-436
Lens Cap (standard). Replacement for all
48PT1 and 48PT2 models.
|
61-4038
20% calibration screen for FE-4 and FE-5
smoke systems.
|
61-4490-1
Lens and Baffle assembly for FE-5 smoke
system source 44DU2-1000.
|
61-4490-2
Lens and baffle assembly for FE-5 smoke
system receiver 47EM4-1000.
|
61-5745-3
Shutter drive circuit board for dual
45UV5-1005 scanners.
|
82-95
Lens holder for 45UV2, 45UV5 and 45RM1/2
|
92-84
FE-4 smoke system reflector.
|
104-7
Alarm bell. 115 VAC. Mounts on 3" or 4"
round box. Three-inch diameter bell rotates
to adjust volume.
|
104-15
Alarm horn. 115VAC. Weatherproof
construction. Also available. P.N 104-16 for
115 VDC; 104-17 for 220VAC; 104-18 for
220VDC.
|
129-72
40% calibration screen for smoke control
27RL1 FE-4.
|
